docs/INSTALL_CENTOS_5.4_dovecot_bind.txt

-
-
-Installation
------------
-
-It is recommended to use a clean (fresh) CentOS 5.4 install. Then follow the steps below to setup your server with ISPConfig 3:
-
-Installation of some basic requirements:
-
-rpm --import /etc/pki/rpm-gpg/RPM-GPG-KEY*
-
-enable the contrib and centosplus repositories.
-
-vi /etc/yum.repos.d/CentOS-Base.repo
-
-1. Edit the file /etc/yum.repos.d/CentOS-Base.repo and edit the lines below.
-
-[base]
-exclude=postfix
-
-[update]
-exclude=postfix
-
-[centosplus]
-enabled=1
-includepkgs=postfix
-
-[contrib]
-enabled=1
-
-rpm --import http://dag.wieers.com/rpm/packages/RPM-GPG-KEY.dag.txt
-
-cd /tmp
-wget http://packages.sw.be/rpmforge-release/rpmforge-release-0.5.1-1.el5.rf.i386.rpm
-rpm -i rpmforge-release-0.5.1-1.el5.rf.i386.rpm
-yum update
-
-You should disable selinux now, as some programs will not start when selinux is enabled:
-
-system-config-securitylevel-tui
-
-then reboot the server.
-
-Then remove the postfix without mysql support
-
-yum remove postfix
-
-1) Install Postfix fron centosplus with mysql support, Dovecot, MySQL, phpMyAdmin with the following command line (on one line!):
-
-yum install ntp httpd mysql-server php php-mysql php-mbstring phpMyAdmin postfix getmail
-
-For 32Bit systems:
-
-rpm -i http://dl.atrpms.net/all/dovecot-1.2.10-2_107.el5.i386.rpm
-rpm -i http://dl.atrpms.net/all/dovecot-sieve-0.1.15-4.el5.i386.rpm
-
-For 64Bit Systems:
-
-rpm -i http://dl.atrpms.net/all/dovecot-1.2.10-2_107.el5.x86_64.rpm
-rpm -i http://dl.atrpms.net/all/dovecot-sieve-0.1.15-4.el5.x86_64.rpm
-
-
-chkconfig --levels 235 mysqld on
-/etc/init.d/mysqld start
-
-chkconfig --levels 235 httpd on
-/etc/init.d/httpd start
-
-chkconfig --levels 235 dovecot on
-/etc/init.d/dovecot start
-
-chkconfig --levels 235 sendmail off
-chkconfig --levels 235 postfix on
-/etc/init.d/sendmail stop
-/etc/init.d/postfix start
-
-
-Set the mysql database password:
-
-/usr/bin/mysql_secure_installation
-
-
-2) Install Amavisd-new, Spamassassin and Clamav (1 line!):
-
-yum install amavisd-new spamassassin clamav clamd unzip bzip2 unrar
-
-sa-update
-chkconfig --levels 235 amavisd on
-chkconfig --levels 235 clamd on
-/usr/bin/freshclam
-/etc/init.d/amavisd start
-/etc/init.d/clamd start
-
-If you use the amavisd from rpmforge (as we do in this guide) and not the one from centos, you will have to do these additional steps:
-
-add the following line in /etc/sysconfig/amavisd:
-
-CONFIG_FILE="/etc/amavisd/amavisd.conf
-
-run:
-
-mkdir /var/run/amavisd /var/spool/amavisd /var/spool/amavisd/tmp /var/spool/amavisd/db
-chown amavis /var/run/amavisd /var/spool/amavisd /var/spool/amavisd/tmp /var/spool/amavisd/db
-ln -s /var/run/clamav/clamd.sock /var/spool/amavisd/clamd.sock
-yum install perl-DBD-mysql
-
-
-3) Install apache, PHP5 and phpmyadmin (1 line!):
-
-yum install php php-devel php-gd php-imap php-ldap php-mysql php-odbc php-pear php-xml php-xmlrpc php-eaccelerator  php-mbstring php-mcrypt php-mhash php-mssql php-snmp php-soap php-tidy curl curl-devel perl-libwww-perl ImageMagick libxml2 libxml2-devel phpmyadmin
-
-
-4) Install pure-ftpd and quota
-
-yum install pure-ftpd quota
-
-chkconfig --levels 235 pure-ftpd on
-/etc/init.d/pure-ftpd start
-
-5) Install bind dns server
-
-yum install bind-chroot
-
-chmod 755 /var/named/
-chmod 775 /var/named/chroot/
-chmod 775 /var/named/chroot/var/
-chmod 775 /var/named/chroot/var/named/
-chmod 775 /var/named/chroot/var/run/
-chmod 777 /var/named/chroot/var/run/named/
-cd /var/named/chroot/var/named/
-ln -s ../../ chroot
-cp /usr/share/doc/bind-9.3.6/sample/var/named/named.local /var/named/chroot/var/named/named.local
-cp /usr/share/doc/bind-9.3.6/sample/var/named/named.root /var/named/chroot/var/named/named.root
-touch /var/named/chroot/etc/named.conf
-
-vi /var/named/chroot/etc/named.conf
-
---------------------------------------------------------------------------------------------------
-//
-// named.conf
-//
-// Provided by Red Hat bind package to configure the ISC BIND named(8) DNS
-// server as a caching only nameserver (as a localhost DNS resolver only).
-//
-// See /usr/share/doc/bind*/sample/ for example named configuration files.
-//
-
-options {
-        listen-on port 53 { 127.0.0.1; };
-        listen-on-v6 port 53 { ::1; };
-        directory       "/var/named/chroot/var/named";
-        dump-file       "/var/named/chroot/var/named/data/cache_dump.db";
-        statistics-file "/var/named/chroot/var/named/data/named_stats.txt";
-        memstatistics-file "/var/named/chroot/var/named/data/named_mem_stats.txt";
-        allow-query     { localhost; };
-        recursion yes;
-};
-
-logging {
-        channel default_debug {
-                file "data/named.run";
-                severity dynamic;
-        };
-};
-
-zone "." IN {
-        type hint;
-        file "named.root";
-};
-
-include "/var/named/chroot/etc/named.conf.local";
---------------------------------------------------------------------------------------------------
-
-
-chkconfig --levels 235 named on
-/etc/init.d/named start
-
-6) Install vlogger dependencies and webalizer
-
-yum install webalizer perl-DateTime-Format-HTTP perl-DateTime-Format-Builder
-
-Installing Jailkit:
-
-yum install gcc
-cd /tmp
-wget http://olivier.sessink.nl/jailkit/jailkit-2.11.tar.gz
-tar xvfz jailkit-2.11.tar.gz
-cd jailkit-2.11
-./configure
-make
-make install
-rm -rf jailkit-2.11*
-
-
-7) Install ISPConfig 3
-
-
-cd /tmp
-wget http://www.ispconfig.org/downloads/ISPConfig-3.0.2.tar.gz
-tar xvfz ISPConfig-3.0.2.tar.gz
-cd ispconfig3_install/install/
-
-Now start the installation process by executing:
-
-php -q install.php
-
-The installer will configure all services like postfix, sasl, courier, etc. for you. A manual setup as required for ISPConfig 2 (perfect setup guides) is not nescessary. To login to the ISPConfig controlpanel, open the following URL in your browser (replace the IP to match your settings!):
-
-http://192.168.0.100:8080/
-
-the default login is:
-
-user: admin
-password: admin
-
-In case you get a permission denied error from apache, please restart the apache webserver process.
-
-Optional:
-
-Install a webbased Email Client
-
-yum install squirrelmail
-
-
-

docs/INSTALL_DEBIAN_4.0.txt

-Installation
------------
-
-It is recommended to use a clean (fresh) Debian etch install where you just selected "Standard System" as the package selection during setup. Then follow the steps below to setup your server with ISPConfig 3:
-
-assign hostname (for example ispconfig)
-
-echo ispconfig.example.com > /etc/hostname
-
-vi /etc/hosts
-and add line similar but appropriate:
-127.0.0.1       localhost.localdomain   localhost
-192.168.0.100   ispconfig.example.com   ispconfig
-
-1) Add the debian volatile repository to the apt sources list:
-
-vi /etc/apt/sources.list
-
-and insert the line:
-
-deb http://volatile.debian.org/debian-volatile etch/volatile main contrib non-free
-
-Then execute these commands to insert the Debian voltaile gpg key to the apt keyring:
-
-cd /tmp
-apt-get install wget
-wget http://www.debian.org/volatile/etch-volatile.asc
-apt-key add etch-volatile.asc
-rm -f etch-volatile.asc
-
-Now we update the package list by executing:
-
-apt-get update
-
-Now Install Postfix, Courier, Saslauthd, MySQL, phpMyAdmin, ntpdate, rkhunter, binutils with the following command line (on one line!):
-
-apt-get install postfix postfix-mysql postfix-doc mysql-client mysql-server courier-authdaemon courier-authlib-mysql courier-pop courier-pop-ssl courier-imap courier-imap-ssl libsasl2 libsasl2-modules libsasl2-modules-sql sasl2-bin libpam-mysql openssl courier-maildrop getmail4 ntp ntpdate rkhunter binutils
-
-Answer the questions from the package manager as follows.
-
-Create directories for web-based administration ? <-- No
-General type of configuration? <-- Internet site
-Mail name? <-- server1.mydomain.tld
- SSL certificate required <-- Ok
-
-...use your own domain name of course ;)
-
-Edit the file /etc/mysql/my.cnf
-
-vi /etc/mysql/my.cnf
-
-and comment out the line
-
-bind-address          = 127.0.0.1
-
-then restart mysql
-
-/etc/init.d/mysql restart
-
-Set the mysql database password:
-
-mysqladmin -u root password yourrootsqlpassword
-mysqladmin -h ispconfig.local -u root password yourrootsqlpassword
-
-
-2) Install Amavisd-new, Spamassassin and Clamav (1 line!):
-
-apt-get install amavisd-new spamassassin clamav clamav-daemon zoo unzip bzip2 arj nomarch lzop cabextract apt-listchanges libnet-ldap-perl libauthen-sasl-perl clamav-docs daemon libio-string-perl libio-socket-ssl-perl libnet-ident-perl zip libnet-dns-perl
-
-3) Install apache, PHP5 and phpmyadmin (1 line!):
-
-apt-get install apache2 apache2.2-common apache2-doc apache2-mpm-prefork apache2-utils libexpat1 ssl-cert libapache2-mod-php5 php5 php5-common php5-gd php5-mysql php5-imap phpmyadmin php5-cli php5-cgi libapache2-mod-fcgid
-
-Then run the following to enable the Apache modules:
-
-a2enmod suexec
-a2enmod rewrite
-a2enmod ssl
-a2enmod actions
-a2enmod include
-
-4) Install pure-ftpd and quota
-
-apt-get install pure-ftpd-common pure-ftpd-mysql quota quotatool
-
-Edit the file /etc/default/pure-ftpd-common
-
-vi /etc/default/pure-ftpd-common
-
-and change the start mode from inetd to standalone. 
-
-Edit the file /etc/inetd.conf
-
-vi /etc/inetd.conf
-
-and comment out the line for the FTP service, so it looks like this:
-
-# ftp   stream  tcp     nowait  root    /usr/sbin/tcpd /usr/sbin/pure-ftpd-wrapper
-
-Then execute:
-
-/etc/init.d/openbsd-inetd restart
-
-
-5) Install mydns
-
-apt-get install mydns-mysql
-
-What is the hostname of the machine on which the database will run? -> localhost
-What is the database name for the MyDNS database? -> mydns
-Would you like to set up the database and tables automatically? -> yes
-What is the username of the MySQL administrator? -> root
-Enter the MySQL administrator password -> yourrootsqlpassword
-Confirm this password -> yourrootsqlpassword
-What is the MyDNS username? -> mydns
-What is the MyDNS user password? -> mydnspassword
-
-The mydns installer is a bit tricky, you will have to select to create a new database for mydns and use a existing mysql user, e.g. the mysql root user. This database is only to fullfill the requirements for the debian pacakge during installation and will not be used by ISPConfig later. ISPConfig will automatically change the mydns configuration files to use the ISPConfig database.
-
-
-6) Install vlogger and webalizer
-
-apt-get install vlogger webalizer
-
-7) Install Jailkit (optional, only needed if you want to use chrroting for SSH users)
-
-apt-get install build-essential autoconf automake1.9 libtool flex bison debhelper
-cd /tmp
-wget http://olivier.sessink.nl/jailkit/jailkit-2.7.tar.gz
-tar xvfz jailkit-2.7.tar.gz
-cd jailkit-2.7
-./debian/rules binary
-cd ..
-dpkg -i jailkit_2.7-1_i386.deb
-rm -rf jailkit-2.7*
-
-8) Install fail2ban (optional but recomended, because the monitor tries to show the log)
-More info at: http://www.howtoforge.com/fail2ban_debian_etch
-
-apt-get install fail2ban
-
-
-9) Install ISPConfig 3
-
-There are two possile scenarios, but not both:
-9.1) Install the latest released version 
-9.2) Install directly from SVN
-
-9.1) Installation of last version from tar.gz
-
-  cd /tmp
-  wget http://www.ispconfig.org/downloads/ISPConfig-3.0.0.9-rc2.tar.gz
-  tar xvfz ISPConfig-3.0.0.9-rc2.tar.gz
-  cd ispconfig3_install/install/
-
-9.2) Installation from SVN
-
-  apt-get install subversion
-  cd /tmp
-  svn export svn://svn.ispconfig.org/ispconfig3/trunk/
-  cd trunk/install
-
-
-9.1+9.2) Now proceed with the ISPConfig installation.
-
-Now start the installation process by executing:
-
-php -q install.php
-
-The installer will configure all services like postfix, sasl, courier, etc. for you. A manual setup as required for ISPConfig 2 (perfect setup guides) is not nescessary. To login to the ISPConfig controlpanel, open the following URL in your browser (replace the IP to match your settings!):
-
-http://192.168.0.100:8080/
-
-the default login is:
-
-user: admin
-password: admin
-
-In case you get a permission denied error from apache, please restart the apache webserver process.
-
-Optional:
-
-Install a webbased Email Client
-
-apt-get install squirrelmail
-ln -s /usr/share/squirrelmail/ /var/www/webmail
-
-Access squirrelmail:
-
-http://192.168.0.100/webmail
-
-
-To configure squirrelmail, run:
-
-/usr/sbin/squirrelmail-configure
-
-----------------------------------------------------------------------------------------------------------
-
-Hints:
-
-debian 4.0 under openvz:
-
-VPSID=101
-for CAP in CHOWN DAC_READ_SEARCH SETGID SETUID NET_BIND_SERVICE NET_ADMIN SYS_CHROOT SYS_NICE CHOWN DAC_READ_SEARCH SETGID SETUID NET_BIND_SERVICE NET_ADMIN SYS_CHROOT SYS_NICE
-do
-  vzctl set $VPSID --capability ${CAP}:on --save
-done
-
-----------------------------------------------------------------------------------------------------------
-
-Optional packages recommended:
-
-denyhosts - a utility to help sys admins thwart ssh crackers
-rsync - fast remote file copy program (for backup)
\ No newline at end of file

docs/INSTALL_DEBIAN_5.0_courier_mydns.txt

-Installation
------------
-
-# It is recommended to use a clean (fresh) Debian lenny install where you just selected "Standard System" as the package selection during
-# setup. Then follow the steps below to setup your server with ISPConfig 3. In this guide "vi" is used as texteditor, but you ofcourse
-# you can use whatever you prefer. You should be root for doing all of this.
-
-
-# Check we have Fully Qualified Domain Name
-
-/bin/hostname
-
-# it should return something like "ispconfig.example.com"
-# if not, then we assign a hostname (for example ispconfig):
-
-echo ispconfig.example.com > /etc/hostname
-/etc/init.d/hostname.sh
-
-vi /etc/hosts
-
-# and add lines similar but appropriate:
-
-127.0.0.1       localhost.localdomain   localhost
-192.168.0.100   ispconfig.example.com   ispconfig
-
-
-
-# Some optional choices
-
-opt0.1) Optionally install SSH-server to get remote shell
-
-apt-get install ssh openssh-server
-
-opt0.2) Optionally if you are not running in virtual machine you can set server clocksync via NTP. Virtual quests get this from the host.
-
-apt-get install ntp ntpdate
-
-opt0.3) Optionally if you want vi editor improvement
-
-apt-get -y install vim-nox
-
-
-# Next is the real deal
-
-1) Install Postfix, Courier, Saslauthd, MySQL, phpMyAdmin, rkhunter, binutils with the following command line (on one line!):
-
-apt-get -y install postfix postfix-mysql postfix-doc mysql-client mysql-server courier-authdaemon courier-authlib-mysql courier-pop courier-pop-ssl courier-imap courier-imap-ssl libsasl2-2 libsasl2-modules libsasl2-modules-sql sasl2-bin libpam-mysql openssl courier-maildrop getmail4 rkhunter binutils
-
-# Answer the questions from the package manager as follows.
-
-Create directories for web-based administration ? <-- No
-General type of configuration? <-- Internet site
-Mail name? <-- server1.mydomain.tld
- SSL certificate required <-- Ok
-
-# ...use your own domain name of course ;)
-
-
-
-# Edit the file /etc/mysql/my.cnf
-
-vi /etc/mysql/my.cnf
-
-# and change the line:
-
-bind-address          = 127.0.0.1
-
-to:
-
-#bind-address          = 127.0.0.1
-
-# then restart mysql
-
-/etc/init.d/mysql restart
-
-2) Install Amavisd-new, Spamassassin and Clamav (1 line!):
-
-apt-get -y install amavisd-new spamassassin clamav clamav-daemon zoo unzip bzip2 arj nomarch lzop cabextract apt-listchanges libnet-ldap-perl libauthen-sasl-perl clamav-docs daemon libio-string-perl libio-socket-ssl-perl libnet-ident-perl zip libnet-dns-perl
-
-# During the installation, the SSL certificates for IMAP-SSL and POP3-SSL are created with the hostname localhost. To change this to the correct hostname (server1.example.com in this tutorial), delete the certificates...
-
-cd /etc/courier
-rm -f /etc/courier/imapd.pem
-rm -f /etc/courier/pop3d.pem
-
-# ... and modify the following two files; replace CN=localhost with CN=server1.example.com (you can also modify the other values, if necessary):
-
-vi /etc/courier/imapd.cnf
-
-[...]
-CN=server1.example.com
-[...]
-
-vi /etc/courier/pop3d.cnf
-
-[...]
-CN=server1.example.com
-[...]
-
-# Then recreate the certificates...
-
-mkimapdcert
-mkpop3dcert
-
-# ... and restart Courier-IMAP-SSL and Courier-POP3-SSL:
-
-/etc/init.d/courier-imap-ssl restart
-/etc/init.d/courier-pop-ssl restart 
-
-
-3) Install apache, PHP5, phpmyadmin, better fastCGI, suexec, Pear and mcrypt (1 line!):
-
-apt-get -y install apache2 apache2.2-common apache2-doc apache2-mpm-prefork apache2-utils libexpat1 ssl-cert libapache2-mod-php5 php5 php5-common php5-gd php5-mysql php5-imap phpmyadmin php5-cli php5-cgi libapache2-mod-fcgid apache2-suexec php-pear php-auth php5-mcrypt mcrypt php5-imagick imagemagick libapache2-mod-suphp libopenssl-ruby
-
-
-# When phpMyAdmin is asking weather to configure itself automatically, select "Apache2"
-
-# Then run the following to enable the Apache modules suexec, rewrite and ssl:
-
-a2enmod suexec rewrite ssl actions include
-
-# restart apache before continuing
-
-/etc/init.d/apache2 restart
- 
-
-4) Install pure-ftpd and quota
-
-apt-get -y install pure-ftpd-common pure-ftpd-mysql quota quotatool
-
-# Enable TLS in pureftpd
-echo 1 > /etc/pure-ftpd/conf/TLS
-mkdir -p /etc/ssl/private/
-openssl req -x509 -nodes -newkey rsa:1024 -keyout /etc/ssl/private/pure-ftpd.pem  -out /etc/ssl/private/pure-ftpd.pem
-chmod 600 /etc/ssl/private/pure-ftpd.pem 
-
-
-# Edit /etc/fstab. Mine looks like this (I added ,usrquota,grpquota to the partition with the mount point /):
-
-vi /etc/fstab
-
-----------------------------------------------------------------------------------------------
-# /etc/fstab: static file system information.
-#
-# <file system> <mount point>   <type>  <options>       <dump>  <pass>
-proc            /proc           proc    defaults        0       0
-/dev/sda1       /               ext3    errors=remount-ro,usrquota,grpquota 0       1
-/dev/sda5       none            swap    sw              0       0
-/dev/hda        /media/cdrom0   udf,iso9660 user,noauto     0       0
-/dev/fd0        /media/floppy0  auto    rw,user,noauto  0       0
-----------------------------------------------------------------------------------------------
-
-# To enable quota, run these commands:
-
-touch /quota.user /quota.group
-chmod 600 /quota.*
-mount -o remount /
-quotacheck -avugm
-quotaon -avug
-
-
-5) Install mydns
-
-apt-get install g++ libc6 gcc gawk make texinfo libmysqlclient15-dev
-
-cd /tmp
-wget http://heanet.dl.sourceforge.net/sourceforge/mydns-ng/mydns-1.2.8.27.tar.gz
-tar xvfz mydns-1.2.8.27.tar.gz
-cd mydns-1.2.8
-./configure
-make
-make install
-
-# Now create the start / stop script for mydns:
-
-vi /etc/init.d/mydns
-
-# and enter the following lines (between the ----- lines):
-
-------------------------------------------------------
-#! /bin/sh
-#
-# mydns         Start the MyDNS server
-#
-# Author:       Philipp Kern <phil@philkern.de>.
-#               Based upon skeleton 1.9.4 by Miquel van Smoorenburg
-#               <miquels@cistron.nl> and Ian Murdock <imurdock@gnu.ai.mit.edu>.
-#
-### BEGIN INIT INFO
-# Provides:          MyDNS
-# Required-Start:    $syslog
-# Should-Start:
-# Required-Stop:
-# Should-Stop:
-# Default-Start:     2 3 4 5
-# Default-Stop:      0 1 6
-# Short-Description: MyDNS Server
-# Description:       MyDNS DNS Server
-### END INIT INFO
-
-set -e
-
-PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
-DAEMON=/usr/local/sbin/mydns
-NAME=mydns
-DESC="DNS server"
-
-SCRIPTNAME=/etc/init.d/$NAME
-
-# Gracefully exit if the package has been removed.
-test -x $DAEMON || exit 0
-
-case "$1" in
-  start)
-        echo -n "Starting $DESC: $NAME"
-        start-stop-daemon --start --quiet \
-                --exec $DAEMON -- -b
-        echo "."
-        ;;
-  stop)
-        echo -n "Stopping $DESC: $NAME"
-        start-stop-daemon --stop --oknodo --quiet \
-                --exec $DAEMON
-        echo "."
-        ;;
-  reload|force-reload)
-        echo -n "Reloading $DESC configuration..."
-        start-stop-daemon --stop --signal HUP --quiet \
-                --exec $DAEMON
-        echo "done."
-        ;;
-  restart)
-        echo -n "Restarting $DESC: $NAME"
-        start-stop-daemon --stop --quiet --oknodo \
-                --exec $DAEMON
-        sleep 1
-        start-stop-daemon --start --quiet \
-                --exec $DAEMON -- -b
-        echo "."
-        ;;
-  *)
-        echo "Usage: $SCRIPTNAME {start|stop|restart|reload|force-reload}" >&2
-        exit 1
-        ;;
-esac
-
-exit 0
----------------------------------------------------------------------------
-
-# now execute:
-
-chmod +x /etc/init.d/mydns
-update-rc.d mydns defaults
-
-6) Install vlogger and webalizer
-
-apt-get install vlogger webalizer
-
-
-7) Install Jailkit (optional, only needed if you want to use chrroting for SSH users)
-
-apt-get install build-essential autoconf automake1.9 libtool flex bison debhelper
-cd /tmp
-wget http://olivier.sessink.nl/jailkit/jailkit-2.11.tar.gz
-tar xvfz jailkit-2.11.tar.gz
-cd jailkit-2.11
-./debian/rules binary
-cd ..
-dpkg -i jailkit_2.11-1_*.deb
-rm -rf jailkit-2.11*
-
-8) Install fail2ban (optional but recomended, because the monitor tries to show the log)
-More info at: http://www.howtoforge.com/fail2ban_debian_etch
-
-apt-get install fail2ban
-
-9) Install ISPConfig 3
-
-cd /tmp
-wget http://www.ispconfig.org/downloads/ISPConfig-3.0.2.tar.gz
-tar xvfz ISPConfig-3.0.2.tar.gz
-cd ispconfig3_install/install/
-
-# Now start the installation process by executing:
-
-php -q install.php
-
-# The installer will configure all services like postfix, sasl, courier, etc. for you. A manual setup as required for ISPConfig 2 (perfect setup guides) is not nescessary. To login to the ISPConfig controlpanel, open the following URL in your browser (replace the IP to match your settings!):
-
-http://192.168.0.100:8080/
-
-# the default login is:
-
-user: admin
-password: admin
-
-# In case you get a permission denied error from apache, please restart the apache webserver process.
-
-
-
-----------------------------------------------------------------------------------------------------------
-Optional:
-
-Install a webbased Email Client
-
-apt-get install squirrelmail
-ln -s /usr/share/squirrelmail/ /var/www/webmail
-
-Access squirrelmail:
-
-http://192.168.0.100/webmail
-
-
-To configure squirrelmail, run:
-
-/usr/sbin/squirrelmail-configure
-
-----------------------------------------------------------------------------------------------------------
-
-Hints:
-
-debian 5.0 under openvz:
-
-VPSID=101
-for CAP in CHOWN DAC_READ_SEARCH SETGID SETUID NET_BIND_SERVICE NET_ADMIN SYS_CHROOT SYS_NICE CHOWN DAC_READ_SEARCH SETGID SETUID NET_BIND_SERVICE NET_ADMIN SYS_CHROOT SYS_NICE
-do
-  vzctl set $VPSID --capability ${CAP}:on --save
-done
-
-----------------------------------------------------------------------------------------------------------
-
-
-Optional recommended packages:
-
-denyhosts - a utility to help sys admins thwart ssh crackers
-rsync - fast remote file copy program (for backup)
-
------------------------------------------------------------------------------------------------------------
-
-Ispc log files rotate, for now manual add but to add in ispc installer:
-
-/etc/logrotate.d/logispc3
-
-/var/log/ispconfig/ispconfig.log {
-	weekly
-	missingok
-	rotate 4
-	compress
-	delaycompress
-}
-/var/log/ispconfig/cron.log {
-	weekly
-	missingok
-	rotate 4
-	compress
-	delaycompress
-}
-
-
------------------------------------------------------------------------------------------------------------
-
-Possible errors and their solutions
-------------------------------------
-
-pureftpd login does not work. Take a look at the syslog, if you find an error message like this:
-Mar 24 16:26:28 ispconfig pure-ftpd: (?@?) [ERROR] Sorry, invalid address given
-
-then pureftpd is not able to resolve the hostname. Name resolving can be disabled with these commands:
-
-echo 'yes' > /etc/pure-ftpd/conf/DontResolve
-/etc/init.d/pure-ftpd-mysql restart
-
-
-
-
-
-

docs/INSTALL_POWERDNS_DEBIAN_5.txt

-
-# Installing PowerDNS on Debian Linux
-----------------------------------------------------------------------------
-
-apt-get install pdns-server pdns-backend-mysql
-
-

docs/Remote_API_docs.txt

+
+
+The remote API documentation is in the remoting_client/API-docs subfolder.